The 72% Solids Super Fast Drying Polyaspartic Coating - made by Spartacote is a 2 layer super resistant resistant polyaspartic coating system that dries within 1-2 hours of application. It is extremely durable against acids/chemicals, abrasions, hot/cold temperatures, oils, and fluids. It applies easily and requires no special skills to install. Can be used outdoors as it does not yellow like epoxies. Gloss finish only. Coverage approximately 250 square ft/gal. Please chose option for gloss or low gloss finish. This Kit comes in 2 Gal (Gloss) and 3.3 Gal Sets (Low Gloss).
Working time 20-25 minutes under standard 70 degree conditions.
Can be used as a topcoat or standalone coating. For colored/pigmented version see ‘Tintable Spartacote’ . Non skid additives can be added to the product or broadcast on. Two coats are required for best results.
Please ensure to order proper amount per square footage needed for 2X coats. Ie. If you are covering a 500 sq.ft garage you will need 4 gallons of product.
Fore 100% solids version of this product please email us at firstname.lastname@example.org for pricing.
2 Gal Set
*Please note depending on how thick or thin you apply the coating coverage will vary. If your floor is more porous it will require more epoxy. If you are applying on new, smooth concrete then you will use less epoxy. Appx coverage is 250 sq.ft per Gal
The Oil Stop Primer is designed for floors where oils spills, grease, petroleum, and other alike chemicals or substances have penetrated deep into the concrete contaminating it. This unique 2 part primer allows epoxy coatings to bond the floor preventing beading on stained surfaces. This product works great with any our epoxy paint coatings but better than that this product will virtually work with any epoxy product on the market.
The Epoxy Trak Textured Roller is required for use with the Commando Coat 500X - High Performance Flexible Urethane Coating. This special roller allows the coating to be evenly distributed due to the textured granules. It also helps prevent uneven applications.
Coverage is 200 sq.ft per roller. This product comes in 4 inch and 9 inch versions.
Highly Durable Textured Roller
1 Textured Roller
200 square feet
The Crack Repair Putty is a two component 100% solids epoxy crack filler that you mix together to fill all types of cracks, dinges, joints expansions, and hairline fractures in your floor. It goes on like ‘spackle’ but is 5X stronger than concrete, and has 4X the bonding power to concrete vs. mortar type crack repairs. It can fill cracks up to 3/16″ deep and several inches wide without the use of aggregates.
To apply simply scoop out equal parts of “A” and “B” (mix ratio of 1:1) and mix on a piece of cardboard until evenly mixed. Then apply with putty knife or trowel just like you would with a painters spackle. It can be coated over IMMEDIATELY, even if the floor is not fully cured yet!
Coverage is 500 lineal feet of 1/8″ x 1/8″ size cracks for the qt size kit and 2,000 lineal feet for the 2 gal kit. You will get less coverage for larger cracks. This product is only available in gray. You can paint epoxy right over it!
Note: This product can also be used on vertical walls.
500 Lineal Feet
The Flash Bond Primer is a specialized one part liquid primer. Used as a pre-treatment for bonding of virtually any coating (epoxies, urethanes, mortar, novolacs). If you have a porous floor or are unaware of the coating that currently exists then this product will work great as a primer for a featured coating. It bonds to metal, wood, tile, fiberglass, linoleum, vinyl, ceramic, glass, composite decking, and virtually any surface. It will dry as off-white and requires no special skills to install. Just roll or bush onto your surface. Flash Bond Primer is also used as a primer for ArmorTop Outdoor Coating for bare concrete or asphalt.
Note: When applying on painted surfaces, plastic, or vinyl siding please ensure to test a small area prior, to assure that the underlying surface will not be affected. We do not recommend this product for use in hot tubs, showers, and baths. Please do not apply in areas where there is continuous or hot water present. Please make sure to wipe down with your floor with denatured alcohol (after you buff) before application.
*Coverage will be affected by type of surface. It will cover less on porous or irregular surfaces such as asphalt.