$3.19
The Commando Coat 200X - 3 Layer Epoxy Flooring Kit is a commercial grade three layer high performance coating system. This kit features a single layer of epoxy primer, single layer of epoxy coating, and standard topcoat along with our decorative flooring chips. This 3 layer floor system is ideal for commercial or home use where the floor is subject to daily use and activity. The 3 layer build up provides you with the a super durable floor that can withstand high impact falls, chemicals, cleaners, car fluids, any other substance that might get onto your floor. It features and easy to clean surface using a mop or wet-vac. This coating is ideal for garages, repair shops, warehouses, and any other flooring that is concrete based. The decorative chips (optional) will hide imperfections and give you floor that wow factor!
You will receive :
We give you everything you need to properly install your epoxy coating.
Choose from over 15 colors for you floor and over 40 solid colors of decorative flecks! Clear and custom epoxy colors are available upon request. Bright colors such as red, yellow, white, and other lighter colors require greater pigmentation. Please inquire to find out pricing.
Please note that VOC laws have recently changed. If you are located in one of these states we will substitute the Standard Topcoat for the Low VOC version which is VOC compliant by EPA standards. Affected States are: CA, CT, DE, IL, IN, MD, MA, ME, NJ, NY, OH, PA, RI, VA, KY and all of Canada.
Please type what color flecks you would like to add to your floor coating in the comments section. We include 5 lbs per 500 sq/ft. You will throw the flecks onto your floor after you lay down the initial epoxy coating and then seal the floor with the clear topcoat. See the Decorative Flecks Page to view all colors.
By the Square Foot. 500 sq.ft Minimum
*Please note depending on how thick or thin you apply the coating coverage will vary. If your floor is more porous it will require more epoxy. If you are applying on new, smooth concrete then you will use less epoxy.
$1.99
The Commando Coat 100X - 2 Layer Epoxy Coating Kit is a two layer two part epoxy coating kit. Simply enter your desired square footage amount and the price will automatically be calculated.
This system features a single layer of epoxy/primer followed by a protective urethane topcoat. This build up of two coatings strengthens the epoxy bond allowing for your floor to resist acids/chemicals, abrasions, hot/cold temperatures, dirt and grim from foot traffic, fluid spills and anything else you might get on your floor! It features and easy to clean surface using a mop or wet-vac. This coating is ideal for warehouses studios, basements, storage areas, retail showrooms and any other residential flooring that is concrete based.
Note: Please note that VOC laws have recently changed. If you are located in one of these states we will manually fill your order with the Low VOC version which is VOC compliant by EPA standards and adjust the price accordingly when processed. CA, CT, DE, IL, IN, MD, MA, ME, NJ, NY, OH, PA, RI, VA, KY and all of Canada.
Choose from over 15 colors for you floor! All colored coatings comes with pigments packs which you add when you are mixing.
OPTIONAL:
Please type what color flecks you would like to add to your floor coating in the comments section. We include 3 lbs per 2 Gal Kit. You will throw the flecks onto your floor after you lay down the initial epoxy coating and then seal the floor with the clear topcoat.
By the Square Foot. 500 sq.ft Minimum
*Please note depending on how thick or thin you apply the coating coverage will vary. If your floor is more porous it will require more epoxy. If you are applying on new, smooth concrete then you will use less epoxy.
$339.00
Product Description
The Single Layer Epoxy Primer is a single layer solvent based epoxy primer. This product has superb chemical, abrasion, and substrate resistance allowing it to withstand most common cleaning chemicals, solvents, fluids and other debris that will get on your floor. It features and easy to clean surface using a mop or wet-vac.
This product comes pre-packaged by weight. All kits should be mixed in their entirety at a 1:1 ratio. You will be able to coat appx 250 sq/ft per gallon at 6 Mils thickness.
We suggest using this primer if you are looking for a multiple layer coated floor as this allows for the additional coat of epoxy to grip to the primer providing stronger bond.
Warning: This product does have an odor so we suggest that other members of the facility you are installing this product in clear the area.
2 Gallons 250-300 sq.ft |
10 Gallons 1,250-1,500 sq.ft |
$125.00
The Single Layer Epoxy Primer Low VOC is a single layer water based epoxy primer. This product has superb chemical, abrasion, and substrate resistance allowing it to withstand most common chemicals, solvents, car fluids and household cleaning products. It features and easy to clean surface using a mop or wet-vac.
This product comes pre-packaged by weight. All kits should be mixed in their entirety at a 4:1 ratio. You will be able to coat appx 250 sq/ft per gallon at 6 Mils thickness.
NOTE: The clear is not water clear and is not suitable for topcoating over previously color coated floors. The clear is suitable as a primer or concrete sealer only.
This product can be used as a primer to build up your floors resistance and maintain the floors longevity. We suggest using this primer if you are looking for a multiple layer coated floor as this allows for the additional coat of epoxy to grip to the primer providing stronger bond. This product can be used in conjuction with most of Epoxy Central products. Please refer product data sheets or contact us with questions.
1 Gallons 250-300 sq.ft |
2 Gallons 500-600 sq.ft |
5 Gallons 1,250-1,500 sq.ft |
$214.99
The 93% Solids Medium Build Epoxy Coating is a single layer self priming epoxy resin coating. This 93% solids medium build epoxy is a 2 part 1 layer coating system. This product features no solvents or fillers and will cure at the thickness applied (between 6-12 mils thick). Big box store epoxies are usually 25-35% solids and dry at 2-3 mils thick.Coating will resist most common chemicals, car fluids and household cleaning products. It features and easy to clean surface using a mop or wet-vac.
You will receive a 2 to 1 ratio of “A” and “B”. You simply mix a “A” and “B” at 2:1. Please make sure to mix thoroughly and only mix as much as you need so as not to waste materials. Coverage will vary depending on desired thickness and density of the floor (125-250 sq/ft per gallon). More porous and rough floors will require more coating yielding a lower coverage range. This product works great with most other Epoxy Central products. Please refer to product data sheets.
Choose from over 15 colors! Clear and custom color are available upon request.
*Clear version is available special order with UV inhibitors to prevent yellowing. Please call or email to order. This product can also be used with the Residential I Military Grade Topcoat, Residential I Military Grade Topcoat Low VOC, and Residential I Standard Topcoat
1 ½ Gallons 260 - 375 sq.ft |
3 Gallons 520 - 750 sq.ft |
15 Gallons 2,600 - 3,750 sq.ft |
$229.99
The 100% Solids High Build Epoxy Coating is a single layer, no VOC epoxy resin coating. This 100% solids high build epoxy is a 2 part, 1 layer coating system. This product features no solvents or fillers and will cure at the thickness applied (between 10-15 mil thick). Big box store epoxies are usually 25-35% solids and dry at 2-3 mils thick. Coating will resist most common chemicals, car fluids and household cleaning products. It features and easy to clean surface using a mop or wet-vac.
You will receive a 2 to 1 ratio of “A” and “B”. You simply mix a “A” and “B” at 2:1. Please make sure to mix thoroughly and only mix as much as you need so as not to waste materials. Coverage will vary from depending on desired thickness and density of the floor (appx. 125 sq/ft per gallon). More porous and rough floors will require more coating yielding a lower coverage range. Aggregate/sand can be added as a filler to make patches and thicker versions. This product works great with any of our topcoat flooring options.
Choose from over 15 colors! Clear and custom color are available upon request. Bright colors such as red, yellow, HH white, and other lighter colors require greater pigmentation. Please inquire to find out pricing.
*Clear version is available special order with UV inhibitors to prevent yellowing. Please call or email to order. This product can also be used with the Residential I Military Grade Topcoat, Residential I Military Grade Topcoat Low VOC, and Residential I Standard Topcoat
1 ½ Gallons 175-250 sq.ft |
3 Gallons 350-500 sq.ft |
15 Gallons 1,750 - 2,500 sq.ft |
$299.00
The Polyurethane Military Grade Topcoat is a single layer 2 component flexible aliphatic polyurethane floor sealer that boosts excellent chemical and abrasion resistance. It works great against weather and is UV stabilized. It features a super resistant nonslip smooth finish that makes it extremely easy to clean using a mop or wet-vac.
This product has a 2:1 mix ratio by volume. Simply mix two gallons of part A with 1 gallon of part B and add the antislip aggregate to the mixture. Please make sure to mix thoroughly and only mix as much as you need so as not to waste. You will be able to coat appx 350 sq/ft per gallon at 5 mils thick.
This product can be used as a topcoat with most other Epoxy Central base and primer coatings and will add an extra protected non slip layer to your floor to help withstand the wear and tear it receives. You can choose to add decorative flecks to your flooring system. Simply add decorative flecks into the epoxy or primer before applying this coating to add texture, hide imperfections and give your floor that wow factor! Choose from hundreds of color variations
If you would like to add more texture to your floor coating please make sure to buy the armor-grip which is a nonskid additive that gets mixed into this topcoat. Simply pour 1 Package per Gallon and mix throughly into your topcoat mixture. Make sure to mix every couple of minutes as the non-skid will fall to the bottom of the mixture.
*Please note that VOC laws have recently changed. If you are located in one of these states please select the Low VOC version which is the same product but VOC compliant by EPA standards. CA, CT, DE, IL, IN, MD, MA, ME, NJ, NY, OH, PA, RI, VA, KY and all of Canada. If you do not select the Low VOC version and are located in one of the above states we will manually fill your order with the Low VOC version and adjust the price accordingly when processed.
**Colors or gloss may be affected by high/low temperature, extreme chemical and lighting exposure.
1½ Gallons 525 sq.ft |
3 Gallons 1,050 sq.ft |
15 Gallons 5,250 sq.ft |
$119.00
The Crack Repair Putty is a two component 100% solids epoxy crack filler that you mix together to fill all types of cracks, dinges, joints expansions, and hairline fractures in your floor. It goes on like ‘spackle’ but is 5X stronger than concrete, and has 4X the bonding power to concrete vs. mortar type crack repairs. It can fill cracks up to 3/16″ deep and several inches wide without the use of aggregates.
To apply simply scoop out equal parts of “A” and “B” (mix ratio of 1:1) and mix on a piece of cardboard until evenly mixed. Then apply with putty knife or trowel just like you would with a painters spackle. It can be coated over IMMEDIATELY, even if the floor is not fully cured yet!
Coverage is 500 lineal feet of 1/8″ x 1/8″ size cracks for the qt size kit and 2,000 lineal feet for the 2 gal kit. You will get less coverage for larger cracks. This product is only available in gray. You can paint epoxy right over it!
Note: This product can also be used on vertical walls.
Quart
500 Lineal Feet |
2 Gal |
$119.00
The Oil Stop Primer is designed for floors where oils spills, grease, petroleum, and other alike chemicals or substances have penetrated deep into the concrete contaminating it. This unique 2 part primer allows epoxy coatings to bond the floor preventing beading on stained surfaces. This product works great with any our epoxy paint coatings but better than that this product will virtually work with any epoxy product on the market.
1/2 Gal 100-125 sq.ft |
2 Gal 400-500 sq.ft |
$349.00
The EC8000X is a low VOC water based epoxy primer and stain blocker. This low VOC product is easy to apply, maintain, and clean on virtually any indoor or outdoor substrate. This product is UV resistant and does not yellow. Decorative flakes can be added to this coating to help hid floor imperfections and give your floor that WOW factor. This product is sold in 2.5 Gal sets for the colored version 1 Gallon sets for the clear. Coverage is appx 300 sq.ft per gal for both colored and clear.
1-2 coats of clear will give the floor a ‘polished concrete’ look at an economical price.
VOC is less than 50g/l, meeting the most stringent California environmental laws in all CA counties.
Fast drying (2-3 hours per coat and can be open to foot traffic in just hours).
EC8000X s a 2-part product and comes in pre-measured containers for easy mixing by simply pouring the Part B into the Part A container, and then mix well. Thickness 3-5 mils. Long working time of approximately 1 hour in normal temperatures. Coverage will vary depending on desired thickness and density of the floor. More porous and rough floors will require more coating yielding a lower coverage.
Please note that the clear has a slight amber cast to it so to avoid any minor ambering of surface apply the clear coat thinly.
If you are looking to add decorative flakes then application will be:
Choose from Gray, Beige, and Clear (Satin Finish) versions.
This product is not suitable for wood substrates. Please refer to our other products that can be used on wood substrates.
Colored 2.5 Gal Set appx. 750 sq.ft |
Clear 1 Gal Set appx. 300 sq.ft |