$119.00
The Oil Stop Primer is designed for floors where oils spills, grease, petroleum, and other alike chemicals or substances have penetrated deep into the concrete contaminating it. This unique 2 part primer allows epoxy coatings to bond the floor preventing beading on stained surfaces. This product works great with any our epoxy paint coatings but better than that this product will virtually work with any epoxy product on the market.
1/2 Gal 100-125 sq.ft |
2 Gal 400-500 sq.ft |
$14.99
The Epoxy Trak Textured Roller is required for use with the Commando Coat 500X - High Performance Flexible Urethane Coating. This special roller allows the coating to be evenly distributed due to the textured granules. It also helps prevent uneven applications.
Coverage is 200 sq.ft per roller. This product comes in 4 inch and 9 inch versions.
Highly Durable Textured Roller
1 Textured Roller 200 square feet |
$119.00
The Crack Repair Putty is a two component 100% solids epoxy crack filler that you mix together to fill all types of cracks, dinges, joints expansions, and hairline fractures in your floor. It goes on like ‘spackle’ but is 5X stronger than concrete, and has 4X the bonding power to concrete vs. mortar type crack repairs. It can fill cracks up to 3/16″ deep and several inches wide without the use of aggregates.
To apply simply scoop out equal parts of “A” and “B” (mix ratio of 1:1) and mix on a piece of cardboard until evenly mixed. Then apply with putty knife or trowel just like you would with a painters spackle. It can be coated over IMMEDIATELY, even if the floor is not fully cured yet!
Coverage is 500 lineal feet of 1/8″ x 1/8″ size cracks for the qt size kit and 2,000 lineal feet for the 2 gal kit. You will get less coverage for larger cracks. This product is only available in gray. You can paint epoxy right over it!
Note: This product can also be used on vertical walls.
Quart
500 Lineal Feet |
2 Gal |
$239.00
The Polyurethane Military Grade Topcoat Low VOC is a single layer 2 component flexible aliphatic polyurethane floor sealer that boosts excellent chemical and abrasion resistance. It works great against weather and is UV stabilized. It features a super resistant nonslip smooth finish that makes it extremely easy to clean using a mop or wet-vac.
This product has a 2:1 mix ratio by volume. Simply mix two gallons of part A with 1 gallon of part B and add the antislip aggregate to the mixture. Please make sure to mix thoroughly and only mix as much as you need so as not to waste. You will be able to coat appx 350 sq/ft per gallon at 5 mils thick.
This product can be used as a topcoat with most other Epoxy Central base and primer coatings and will add an extra protected non slip layer to your floor to help withstand the wear and tear it receives. You can choose to add decorative flecks to your flooring system. Simply add decorative flecks into the epoxy or primer before applying this coating to add texture, hide imperfections and give your floor that wow factor! Choose from hundreds of color variations
If you would like to add more texture to your floor coating please make sure to buy the armor-grip which is a nonskid additive that gets mixed into this topcoat. Simply pour 1 Package per Gallon and mix throughly into your topcoat mixture. Make sure to mix every couple of minutes as the non-skid will fall to the bottom of the mixture.
*Please note that VOC laws have recently changed. If you are located in one of these states then this product is compliant by EPA standards. CA, CT, DE, IL, IN, MD, MA, ME, NJ, NY, OH, PA, RI, VA, KY and all of Canada.
**Colors or gloss may be affected by high/low temperature, extreme chemical and lighting exposure.
1½ Gallons 50-550 sq.ft |
3 Gallons 1,000-1,100 sq.ft |
15 Gallons 5,000 -5,500 sq.ft |
$499.00
The 72% Solids Super Fast Drying Polyaspartic Coating - made by Spartacote is a 2 layer acid and chemical resistant polyaspartic coating system that dries within 1-2 hours of application. It is extremely durable against acids/chemicals, abrasions, hot/cold temperatures, oils, and fluids. It applies easily and requires no special skills to install. Can be used outdoors as it does not yellow like epoxies. Gloss finish only (can be top-coated with the Flex SB Low Gloss for low gloss requirements. Please email directly to inquire). Working time 15-20 minutes under standard 70 degree conditions.
This product features a 2 step process. First apply the polyaspartic coating with flecks (optional). Wait 2-3 hours for the coat to dry and then apply a second coat. This coating is best used where time is of the essence. Working time after mixing each batch is appx 20 minutes depending on temperature. The Super-Fast Drying Industrial Polyaspartic comes standard in 'clear' and is field tinted with our pigment packs. Colored Flecks can be added to this system but if you order this we will automatically fill the order will clear gloss topcoat.
Product Information:
Choose from over 15 colors for you floor! Custom color are available upon request. Bright colors such as red, yellow, white, and other lighter colors require greater pigmentation. Please inquire to find out pricing.
Please type what color flecks you would like to add to your floor coating in the comments section. We include 3 lbs per 2 Gal Kit. You will throw the flecks onto your floor after you lay down the initial epoxy coating and then seal the floor with the clear gloss topcoat.
IF YOU DO NOT PROVIDE A FLECK COLOR WE WILL NOT SEND ANY FLECKS.
Please ensure to order proper amount per square footage needed for 2X coats. Ie. If you are covering a 500 sq.ft garage you will need 4 gallons of product.
Fore 100% solids version of this product please email us at info@epoxycentral.com for pricing.
2 Gal Set 500 sq.ft |
4 Gal Set 1000 sq/ft |
10 Gal Set 2500 sq/ft |
*Please note depending on how thick or thin you apply the coating coverage will vary. If your floor is more porous it will require more epoxy. If you are applying on new, smooth concrete then you will use less epoxy. Appx covergae is 250 sq.ft per Gal
$159.99
EC-1X is a three component 100% solids epoxy mortar designed for cove base surface applications. This product has specially selected aggregate and ingredients to provide easy construction of cove bases with the use of a marginal trowel or other cove base application tools. We include the Cover Mortar Primer with purchase of this product. We also sell the coving application tool we recommend for installation of this product.
Components
Instructional Video Below!
$59.00
The curved hand trowel coving tool is designed for making 1/4" inch round coves on virtually any floor. This specially manufactured tool allows for you to make a smooth transition between the wall and the floor as needed. We recommend using this tool in bar backs, restaurants, cooking environment, or any other food processing type facility that requires such a cove to be present. This will help to avoid dirt, food, or any other waste being trapped on the surrounding floors edges. This product can be used with our Epoxy Mortar Resin Kit to make mortar or our Cove Mortar Kits.
We also carry cove strips. Please contact our office to find out more information.
$1.99
The Commando Coat 100X - 2 Layer Epoxy Coating Kit is a two layer two part epoxy coating kit. Simply enter your desired square footage amount and the price will automatically be calculated.
This system features a single layer of epoxy/primer followed by a protective urethane topcoat. This build up of two coatings strengthens the epoxy bond allowing for your floor to resist acids/chemicals, abrasions, hot/cold temperatures, dirt and grim from foot traffic, fluid spills and anything else you might get on your floor! It features and easy to clean surface using a mop or wet-vac. This coating is ideal for warehouses studios, basements, storage areas, retail showrooms and any other residential flooring that is concrete based.
Note: Please note that VOC laws have recently changed. If you are located in one of these states we will manually fill your order with the Low VOC version which is VOC compliant by EPA standards and adjust the price accordingly when processed. CA, CT, DE, IL, IN, MD, MA, ME, NJ, NY, OH, PA, RI, VA, KY and all of Canada.
Choose from over 15 colors for you floor! All colored coatings comes with pigments packs which you add when you are mixing.
OPTIONAL:
Please type what color flecks you would like to add to your floor coating in the comments section. We include 3 lbs per 2 Gal Kit. You will throw the flecks onto your floor after you lay down the initial epoxy coating and then seal the floor with the clear topcoat.
By the Square Foot. 500 sq.ft Minimum
*Please note depending on how thick or thin you apply the coating coverage will vary. If your floor is more porous it will require more epoxy. If you are applying on new, smooth concrete then you will use less epoxy.
$449.00
The 72% Solids Super Fast Drying Polyaspartic Coating - made by Spartacote is a 2 layer super resistant resistant polyaspartic coating system that dries within 1-2 hours of application. It is extremely durable against acids/chemicals, abrasions, hot/cold temperatures, oils, and fluids. It applies easily and requires no special skills to install. Can be used outdoors as it does not yellow like epoxies. Gloss finish only. Coverage approximately 250 square ft/gal. Please chose option for gloss or low gloss finish. This Kit comes in 2 Gal (Gloss) and 3.3 Gal Sets (Low Gloss).
Working time 20-25 minutes under standard 70 degree conditions.
Can be used as a topcoat or standalone coating. For colored/pigmented version see ‘Tintable Spartacote’ . Non skid additives can be added to the product or broadcast on. Two coats are required for best results.
Product Information:
Please ensure to order proper amount per square footage needed for 2X coats. Ie. If you are covering a 500 sq.ft garage you will need 4 gallons of product.
Fore 100% solids version of this product please email us at info@epoxycentral.com for pricing.
2 Gal Set 500 sq.ft |
*Please note depending on how thick or thin you apply the coating coverage will vary. If your floor is more porous it will require more epoxy. If you are applying on new, smooth concrete then you will use less epoxy. Appx coverage is 250 sq.ft per Gal
$299.00
The Polyurethane Military Grade Topcoat is a single layer 2 component flexible aliphatic polyurethane floor sealer that boosts excellent chemical and abrasion resistance. It works great against weather and is UV stabilized. It features a super resistant nonslip smooth finish that makes it extremely easy to clean using a mop or wet-vac.
This product has a 2:1 mix ratio by volume. Simply mix two gallons of part A with 1 gallon of part B and add the antislip aggregate to the mixture. Please make sure to mix thoroughly and only mix as much as you need so as not to waste. You will be able to coat appx 350 sq/ft per gallon at 5 mils thick.
This product can be used as a topcoat with most other Epoxy Central base and primer coatings and will add an extra protected non slip layer to your floor to help withstand the wear and tear it receives. You can choose to add decorative flecks to your flooring system. Simply add decorative flecks into the epoxy or primer before applying this coating to add texture, hide imperfections and give your floor that wow factor! Choose from hundreds of color variations
If you would like to add more texture to your floor coating please make sure to buy the armor-grip which is a nonskid additive that gets mixed into this topcoat. Simply pour 1 Package per Gallon and mix throughly into your topcoat mixture. Make sure to mix every couple of minutes as the non-skid will fall to the bottom of the mixture.
*Please note that VOC laws have recently changed. If you are located in one of these states please select the Low VOC version which is the same product but VOC compliant by EPA standards. CA, CT, DE, IL, IN, MD, MA, ME, NJ, NY, OH, PA, RI, VA, KY and all of Canada. If you do not select the Low VOC version and are located in one of the above states we will manually fill your order with the Low VOC version and adjust the price accordingly when processed.
**Colors or gloss may be affected by high/low temperature, extreme chemical and lighting exposure.
1½ Gallons 525 sq.ft |
3 Gallons 1,050 sq.ft |
15 Gallons 5,250 sq.ft |
$2.29
Commando Coat 500X - High Performance Flexible Urethane Coating, single-pack, totally flexible, slip-resistant, waterproof protective polyurethane coating with self-contained recycled rubber granules for an attractive tough textured finish. Simply enter your desired square footage amount and the price will automatically be calculated.
When exposed to atmospheric moisture, Commando Coat 500X undergoes a chemical curing process which changes it from a liquid to a tough polyurethane membrane. It has excellent abrasion and chemical resistance. It is easy to apply, simply just roll it out! Ideal for boat decks, balconies, patios, houseboats, salt water exposure, docks, sidewalks, and thousands of other uses.
Commando Coat 500X is available in 4 versions: Indoor Smooth @ $2.29/sq ft, Indoor Textured @ $3.29/sq ft, Outdoor Smooth @ $2.99/ft, and Outdoor Textured @ 3.99/sq ft. *Clear color is not available in indoor version, only outdoor. Textured includes 1 coat of smooth, 1 coat of textured.
Minimum order is 150 square feet.
If ordering Textured version, please order 1 textured roller per 200 square feet.
Please note that colors of textured Commando Coat 500X are greatly affected by the addition of granules (which make it textured rather than smooth). We strongly advise you to order samples if color is an important factor.
Smooth |
Indoor |
*By the Square Foot. 150 sq.ft Minimum. Please note depending on how thick or thin you apply the coating coverage will vary.
$89.99
The Epoxy Mortar Patch Kit is a 3 component 100% solids epoxy mortar. Designed for application uses where excellent wear resistance and strength is necessary such as pallet jacks, forklifts, heavy traffic areas and steel-wheeled equipment.
Each kit is comprised of 2 components of A & B along with the special aggregate. All 3 components get mixed together to form the super strong and durable epoxy mortar that is troweled onto the floor. This product exhibits amazing adhesion and resists ‘pop out’ like cement-type patches.
2 Gal Kit (.11 CU FT) 5.3 sq ft @ 1/4″ thick |
5 Gal Kit (.45 CU FT) 21.6 sq ft @ 1/4″ thick |
Bulk Kit (2.25 CU FT) 108 sq ft @ 1/4″ thick |
Sign up to get the latest on sales, new releases and more …
© 2023 Epoxy Central. All rights reserved Powered by Shopify