The EC8000X is a low VOC water based epoxy primer and stain blocker. This low VOC product is easy to apply, maintain, and clean on virtually any indoor or outdoor substrate. This product is UV resistant and does not yellow. Decorative flakes can be added to this coating to help hid floor imperfections and give your floor that WOW factor. This product is sold in 2.5 Gal sets for the colored version 1 Gallon sets for the clear. Coverage is appx 300 sq.ft per gal for both colored and clear.
1-2 coats of clear will give the floor a ‘polished concrete’ look at an economical price.
VOC is less than 50g/l, meeting the most stringent California environmental laws in all CA counties.
Fast drying (2-3 hours per coat and can be open to foot traffic in just hours).
EC8000X s a 2-part product and comes in pre-measured containers for easy mixing by simply pouring the Part B into the Part A container, and then mix well. Thickness 3-5 mils. Long working time of approximately 1 hour in normal temperatures. Coverage will vary depending on desired thickness and density of the floor. More porous and rough floors will require more coating yielding a lower coverage.
Please note that the clear has a slight amber cast to it so to avoid any minor ambering of surface apply the clear coat thinly.
If you are looking to add decorative flakes then application will be:
Choose from Gray, Beige, and Clear (Satin Finish) versions.
This product is not suitable for wood substrates. Please refer to our other products that can be used on wood substrates.
2.5 Gal Set
appx. 750 sq.ft
1 Gal Set
appx. 300 sq.ft
Pro Renew Wood and Concrete Resurfacer is a specially formulated eco-friendly textured liquid coating that can be applied to and wood or concrete surface to bring it back to life and avoid expensive replacement. This scientifically engineered formula is not a paint or stain, but a 1-part (no mixing) water based thick coating that is designed to be applied to wood or concrete surfaces that show imperfections and surface damage from weather conditions, sunlight exposure, moisture, cracks, mold, and discoloration. Pro Renew acts as a liquid resurfacing coating that ’sits’ on the surface but adheres tenaciously (unlike stains or paints that soak in, and epoxies that are not UV stable) and provides a brand new slip-resistant surface. Gives the effect of replacing at a fraction of the cost.
Available in 2 Gallon Kits. Lighter colors and older/more porous wood can yield less coverage. ‘Smooth’ high solids acrylic version is available for painting wood uprights, stairs and between boards. This product is available in 25 colors!
Please Note: This product is not recommended for areas that have standing water or where water does not drain properly. Contact our office for coatings for these types of areas. Pail contents 3.75 gals if not tinted, 4 gals with tint. Pro Renew Wood/Concrete Resurfacer is made in batches and color tints will vary slightly from batch to batch. Please make sure to order enough material for your entire job to avoid discoloration in future applications. If this color shift does occur, it can be corrected by putting on a coat of the Smooth Version).Pail contents 3.75 gals if not tinted, 4 gals with tint.
*2 coats are required for proper performance and warranty coverage. Please note that it is mandatory to use our special textured foam roller pad to apply for the warranty coverage.
Pro Renew Wood Primer is required for all applications to wood in order to obtain the lifetime warranty. Please use our Use our Pro Flash Bond Primer for composite (Trex type) decking.
50-100 sq.ft per gallon
*Lighter colors and older/more porous wood can yield less coverage
The Flash Bond Primer is a specialized one part liquid primer. Used as a pre-treatment for bonding of virtually any coating (epoxies, urethanes, mortar, novolacs). If you have a porous floor or are unaware of the coating that currently exists then this product will work great as a primer for a featured coating. It bonds to metal, wood, tile, fiberglass, linoleum, vinyl, ceramic, glass, composite decking, and virtually any surface. It will dry as off-white and requires no special skills to install. Just roll or bush onto your surface. Flash Bond Primer is also used as a primer for ArmorTop Outdoor Coating for bare concrete or asphalt.
Note: When applying on painted surfaces, plastic, or vinyl siding please ensure to test a small area prior, to assure that the underlying surface will not be affected. We do not recommend this product for use in hot tubs, showers, and baths. Please do not apply in areas where there is continuous or hot water present. Please make sure to wipe down with your floor with denatured alcohol (after you buff) before application.
*Coverage will be affected by type of surface. It will cover less on porous or irregular surfaces such as asphalt.
Commando Coat 500X - High Performance Flexible Urethane Coating, single-pack, totally flexible, slip-resistant, waterproof protective polyurethane coating with self-contained recycled rubber granules for an attractive tough textured finish. Simply enter your desired square footage amount and the price will automatically be calculated.
When exposed to atmospheric moisture, Commando Coat 500X undergoes a chemical curing process which changes it from a liquid to a tough polyurethane membrane. It has excellent abrasion and chemical resistance. It is easy to apply, simply just roll it out! Ideal for boat decks, balconies, patios, houseboats, salt water exposure, docks, sidewalks, and thousands of other uses.
Commando Coat 500X is available in 4 versions: Indoor Smooth @ $2.29/sq ft, Indoor Textured @ $3.29/sq ft, Outdoor Smooth @ $2.99/ft, and Outdoor Textured @ 3.99/sq ft. *Clear color is not available in indoor version, only outdoor. Textured includes 1 coat of smooth, 1 coat of textured.
Minimum order is 150 square feet.
If ordering Textured version, please order 1 textured roller per 200 square feet.
Please note that colors of textured Commando Coat 500X are greatly affected by the addition of granules (which make it textured rather than smooth). We strongly advise you to order samples if color is an important factor.
*By the Square Foot. 150 sq.ft Minimum. Please note depending on how thick or thin you apply the coating coverage will vary.
The 72% Solids Super Fast Drying Polyaspartic Coating - made by Spartacote is a 2 layer acid and chemical resistant polyaspartic coating system that dries within 1-2 hours of application. It is extremely durable against acids/chemicals, abrasions, hot/cold temperatures, oils, and fluids. It applies easily and requires no special skills to install. Can be used outdoors as it does not yellow like epoxies. Gloss finish only (can be top-coated with the Flex SB Low Gloss for low gloss requirements. Please email directly to inquire). Working time 15-20 minutes under standard 70 degree conditions.
This product features a 2 step process. First apply the polyaspartic coating with flecks (optional). Wait 2-3 hours for the coat to dry and then apply a second coat. This coating is best used where time is of the essence. Working time after mixing each batch is appx 20 minutes depending on temperature. The Super-Fast Drying Industrial Polyaspartic comes standard in 'clear' and is field tinted with our pigment packs. Colored Flecks can be added to this system but if you order this we will automatically fill the order will clear gloss topcoat.
Choose from over 15 colors for you floor! Custom color are available upon request. Bright colors such as red, yellow, white, and other lighter colors require greater pigmentation. Please inquire to find out pricing.
Please type what color flecks you would like to add to your floor coating in the comments section. We include 3 lbs per 2 Gal Kit. You will throw the flecks onto your floor after you lay down the initial epoxy coating and then seal the floor with the clear gloss topcoat.
IF YOU DO NOT PROVIDE A FLECK COLOR WE WILL NOT SEND ANY FLECKS.
Please ensure to order proper amount per square footage needed for 2X coats. Ie. If you are covering a 500 sq.ft garage you will need 4 gallons of product.
Fore 100% solids version of this product please email us at email@example.com for pricing.
2 Gal Set
4 Gal Set
10 Gal Set
*Please note depending on how thick or thin you apply the coating coverage will vary. If your floor is more porous it will require more epoxy. If you are applying on new, smooth concrete then you will use less epoxy. Appx covergae is 250 sq.ft per Gal